How to setup Netgear Wi-Fi extender

Connect the provided antennas to the router:
 Of course, when you want to set up your desktop extender, you will do this. Don’t worry; the antennas are attached if you purchased a wall extender, so point them upward.
●      It will be fantastic if you complete the basic setup of the extender and wireless router in the same room as your home. Obviously, you can also move it to your favorite area when you complete the setup perfectly.
●      If you have a wireless router with WPS, please utilize this method. If you do not have enough knowledge about WPS and what to do: simply search the WPS button of the router. Yes, button response, hat WPS, Push n’ Connect, PBC, Wi-Fi Simple Config, Quick Secure Setup(QSS).
 
 
Connect the extender to a power :
 
If you are a desktop extender user, use the power wire connecting the box to link the unit to an outlet. But in a wall extender, plug directly into the wall outlet as usual.
 
●      If you see the power LED does not turn on, tap the power on/off button and check the extender; it’s on.
 
 
Then Press the WPS button on the Netgear extender:
 
Obviously, you are thinking about how to check the WPS signal! A small padlock radiating with a curved line is present. So, you can see the extender to start checking for the router’s WPS network.
 
 
After that, press the WPS button on the wireless router:
When the extender and the router are successfully connected with WPS, you can observe the extender’s WPS LED light. Yes, of course, it will
turn green.
 
 
●      You can easily extend that band if you have a 5GHz supported router. Then again, press the WPS button of your extender and also press the router’s WPS button.
Put your extender halfway between the router and the location with poor connection Wi-Fi:
 
If you set up the router and the extender in the same room of your home, carefully unplug the extender. Yes, you can easily plug it back into your new location. Significantly it would be best if you need a better signal, so properly check the setup of the extender and router range in the permanent place.

Connected the provided antennas to the router:
 
When setup a Netgear Wi-Fi extender on a desktop, firstly, you attach the provided antennas to the router. But in the wall extender, the usable antennas are connected automatically. So, you need only point them upward.
 
●      It will be fantastic if your extender and wireless router’s initial setup is completed in the same room. When setup is finished, you can move it to the desired area.
●      If any situation wireless router does not support WPS, apply this technique. If your router is connected to WPS, you can find the button pointed to WPS, Push n’ Connect, PBC, Wi-Fi Simple Config, and Quick Secure Setup(QSS), which also have a padlock icon.
 
 
Plug the extender into a power :
 
If you are a desktop extender user, use a power cable that came in the box to connect the unit to an outlet. You need to know that if you have a wall extender, carefully plug it directly into the wall outlet.
 
●      If the power LED does not turn on, please press the power on/off button and wait a few seconds. Obviously, the extender is on.
 
Connect your computer device to the extender:
 
You can easily do this step. You will need to disconnect the computer from the existing Wi-Fi network. And then, you can connect the computer to the NETGEAR_EXT. The significant fact is that password is not necessary for this process.
 
Open the link https://www.mywifiext.net on your computer:
 
In your web browser, search this link, and this link helps to open the Installation Assistant.
 
 
●      Of course, you must check that your device is connected correctly to the NETGEAR_EXT wireless network. If it is connected, see this step work successfully.
 
Choose your wireless network and press Next:
If you have both 2GHz and 5GHz router supporters, you can choose both bands as per your choice.
 
Put your wireless network password and click Next:
You can use this password whenever you connect Wi-Fi to your computer, phone, tablet, or other devices.
 
●      If you consider using a dual-band setup, enter the password into the blanks for both bands.
 
 
Click Next when successfully connected:
 
Check the bottom of the screen that appears the network name(s) and also the phrase(s) “Same as existing network password.” Then easily extender will connect to the router.
 
 
Click Continue to finish the setup:
You can close your browser window when you finish the setup.
 
You need to put the extender halfway between the router and the location with poor Wi-Fi:
 
●      If your setup Netgear Wi-Fi extender and router is in the same room, unplug it. Then plug the extender again in at its new place.
●      Of course, you can get a great signal; this is possible if the new location of the extender needs to be in the router’s range.
 
 
Turn on the extender and check the lights:
●      Depending on the model, you will see either a router light or “2GHz” and “5GHz” lights.
●       As long as the light(s) are green or amber, If the extender has a great connection with the router, you will be sure the light is green and longer. If any case, the light is red, you need the extender close to the router until the light isn’t red anymore.